Gliderol remote programming starts with the motor's name
The Door Hero is not connected with Gliderol. The steps here come from Gliderol's own manuals and support pages, and each one names the opener it was written for.
Before any button, Gliderol's remote help page asks you to read the name on the motor's casing, such as Genesis, Glidermatic GRD or Optima. Every model codes remotes its own way, so a sequence meant for one Gliderol opener won't carry over to the next.
People looking up a Gliderol reset usually want one of two things. Either the opener should forget every remote, which Gliderol calls erasing, or the motor needs a restart after it has played up. Both are below. For how remote coding works on any make, see how to program a garage door remote.
Genesis and Genesis Optima: coding a remote
Press CODE on the opener
Gliderol's remote page says the display then shows -. -. on the opener.
Press and hold the remote button
Use the button you want to open this door with, and keep holding it until the dots on the display flash.
Let go of CODE quickly
A press is all it takes. Hold CODE for more than 8 seconds and a Genesis erases every remote it knows, and the dots disappear.
Glidermatic Heavy Duty and Dual: coding a remote
Hold ENTER for 2 seconds
Gliderol describes ENTER as the square button.
Move to Learn
Step through with the UP and DOWN arrows until the Learn light comes on, then press ENTER.
Press the remote button while the indicator is lit
Gliderol says one beep means the remote is coded, and two beeps mean the opener already had it in memory.
Rollamatic GEN II: coding a handset
Hold ENTER for 2 seconds
The Rollamatic GEN II user manual starts both coding and erasing this way.
Choose Learn
Use the UP and DOWN buttons to reach Learn, then press ENTER.
Hold the big button on the handset
Keep it down until the opener beeps. One beep is a success; two beeps mean that handset is stored already.
Be ready before you start
The manual says the opener leaves learn mode after 3 seconds, so have the handset in your hand before you press ENTER.
Older Glidermatic GRD and G+ Universal: coding at the circuit board
Older Glidermatic GRD openers have a rectangular control box, and Gliderol's remote page says their remotes are coded on the circuit board inside it. Set the jumpers JP1, JP2 and JP3 as the manual for your model shows, press LEARN (marked 8) once so the learn LED (8A) lights, then press the remote key. When the LED goes out, the remote has been taken.
A G+ Universal opener also keeps LEARN on its circuit board. Press it once: the LED lights and the unit beeps three times. Then press the button on the remote. A single beep means success, while two beeps say that remote was stored before.
Adding a remote from one that works: GRD and GTS2000
Gliderol's owner's manuals for the Glidermatic GRD and the GTS2000 describe a second route, using a remote that already opens the door. On that working remote, hold OPEN and STOP together for 2 seconds. The opener answers with 3 beeps to show it is in Learn Mode. Then press the key you want on the new remote: one beep and it is coded, two beeps and it was in memory already.
Those manuals number the keys as well. Key 1 is STOP, key 2 is OPEN and key 3 is CLOSE.
None of this is copying. Gliderol says its modern remotes use rolling codes that change with every press, so they cannot be copied; the working remote simply puts the opener into Learn Mode for the new one.
Erasing every remote: Gliderol openers side by side
| How to erase all remotes | Remotes it holds | |
|---|---|---|
| Genesis and Genesis Optima | Hold CODE for more than 8 seconds, until the dots disappear | Up to 15 |
| Glidermatic Heavy Duty and Dual | Go to Learn, then hold ENTER for 5 seconds until the indicator goes out | Up to 10 handsets |
| Older Glidermatic GRD (rectangular box) | Hold LEARN on the board for 5 seconds | Up to 10 handsets |
| G+ Universal | Hold LEARN for 10 seconds: the LED goes out and the unit gives 3 beeps | Up to 10 handsets |
| Rollamatic GEN II | Hold ENTER for 2 seconds, go to Learn, then hold ENTER for 5 seconds until the indicator dims | Check the manual for your model |
After an erase
An erase clears the lot, so every remote you mean to keep has to be coded back in afterwards. It is the step to take when a remote has gone missing or a former owner may still hold one. Other makes are covered in resetting a garage door opener.
Restarting a Gliderol motor after a blackout or a fault
The other kind of Gliderol reset is a restart. Gliderol's motor page says most of its motors hold their programming through a power outage. When one is misbehaving, it suggests cutting the power for 60 seconds and reconnecting it, then turning to the manual for your model if the trouble carries on.
That page also says the travel limits usually survive an outage while the remote codes may not. If the remotes went quiet after a blackout, code them in again with the steps above.
On a Genesis or Optima, an IR error means the photo safety sensors are switched on but are either not working or not connected, Gliderol says. That is a sensor fault rather than a remote one, and the garage door safety sensor guide covers it.
Batteries, lost codes and Vacation Mode: where Gliderol's pages differ
Gliderol's documents don't all agree, so here is each one in its own words.
After a battery change. Gliderol's remote help page says a new battery doesn't mean reprogramming the remote, and puts battery life at 18 to 24 months of normal daily use. Yet the same page says a remote with a working light and a door that ignores it has likely lost its programming, something it says commonly happens after a power outage or a battery swap. If a fresh battery brings the light back but not the door, code that remote again.
Which battery. The remote page says most Gliderol remotes run on two CR2016 3V lithium cells, and the GRD and GTS2000 manuals also list two 3V CR2016 batteries. The Rollamatic GEN II user manual, though, says its remote takes one 3V CR2032. Open the case and read the cell before you buy a replacement.
Vacation Mode. This locks out every remote signal so no transmitter can open the door. The remote page switches it on by holding STOP and CLOSE together for 3 seconds, but the Rollamatic GEN II manual gives 5 seconds for the same keys. How to switch it off is in the manual for your model. If every remote in the house stopped at once, it is worth ruling out.
Universal remotes, older motors and a remote that got wet
Gliderol strongly advises against universal remotes. Its remote page says they often lack the rolling code security of Gliderol's own remotes and may not suit the opener at all.
Age counts too. Much older Gliderol motors ran on fixed codes, and Gliderol says its G+ rolling code remotes won't work with them; on a motor past 15 to 20 years, check that a new remote suits it before you buy.
Dropped one in a puddle? Gliderol says a wet remote can sometimes be saved. Open the case, take the batteries out and leave it to dry for at least 24 to 48 hours, pressing no buttons while it is wet, then fit fresh batteries and test it.
Button cells, and a door in full view
Australia's button battery information standard says a lithium button battery can cause severe or fatal injuries in 2 hours or less if it is swallowed, so keep spare cells locked away and get medical help immediately if a child may have swallowed one. Try every newly coded remote with the door in sight and the doorway clear. Gliderol's maintenance guide warns that defective garage doors can be a serious hazard, and its troubleshooting page says never to adjust or repair door springs yourself.
What to tell the door specialist
- That it is a Gliderol, and the motor name printed on the casing
- Whether it is a roller door or a sectional door
- What the opener did when you tried: the beeps, the lights or an IR error
- How many remotes you have, and whether one is lost
- Whether the remotes have already been erased
- Roughly how old the motor is, if you know
What you can do, and what to leave
You can
- Code a remote using the steps Gliderol gives for your opener
- Restart the motor by turning its power off for 60 seconds
- Dry out a wet remote and fit new batteries
Leave to a door specialist
- A remote that still won't code after the steps for your model
- An IR error that won't clear
- A motor that runs but doesn't move the door
- Anything to do with the door's springs
What we would do
Count while you hold. On a Genesis, a press of CODE adds a remote but a hold past 8 seconds wipes them all, so gather every remote in the house before you start. If the memory does get cleared, you can code each one straight back in without hunting for the spare.
Repairs, servicing and motors
Once the remotes work, anything mechanical is a different job. Servicing, repairs and motor replacement on a Gliderol, and what its warranty asks for, are on the Gliderol garage door repairs page.